一、廢金屬：【磷銅、紅銅、杯士銅、白銅、紫銅、青銅(62#、65#)、黃銅、漆包線銅、銅屑、鋁、不銹鋼(316.316L.304.301.202)、不銹鐵、鋅合金(渣)、鉛、工業鐵、鍍金、鍍銀制品等廢五金廢有色金屬回收】二、廢電子：【電子腳、含銀錫、無鉛錫、含鉛錫、錫渣、錫條、錫線..

回收PC水口料注塑工藝的介紹　1、塑料的處理　　PC塑料的吸水率較大，加工前一定要預熱干燥，純PC干燥120℃，改性PC一般用110℃溫度干燥4小時以上。干燥時間不能超過10小時。一般可用對空擠出法判斷干燥是否足夠。再生料的使用比例可達20%。在某些情況下，可100%的使用再..

如何監督注塑廠來保證產品的質量呢，就是說我們怎樣用普通的方法來檢測出塑膠的純度或是增加了多少的水口料，下面我們一起來分析下如何分辨塑膠產品中是否加入了水口料

回收水口料也應視其生產時產品之用料好壞而定，如果用的全新料則可以用來生產深顏色的產品，較好是黑色，如果是用的回收水口料生產的話則只可生產質量要求比較低的產品；一般水口料加入的比例不宜太大25%左右為宜。水口料重復使用會使塑料性能降低，而使用熱流道系統沒有..